Contents
Introduction
This Module covers the quantification frameworks and equations for calculating market leakage emissions, .
Market leakage is the change in emissions outside a Project's system boundary that occurs when Project activities affect the supply of, or demand for, a commodity traded in a market. Markets respond in three ways, each covered in its own Section. Where a Project consumes an input that would have gone to a different end use, other consumers may turn to substitute products (Section 3). Where a Project displaces agricultural production, land elsewhere is converted to replace it, also known as indirect land use change (ILUC; Section 4). Where a Project reduces timber production by delaying or preventing harvests locally, harvesting shifts to other regions (Section 5).
This Module is intended for use in conjunction with other Isometric Protocols and Modules, and is applicable when it is explicitly referenced within a Protocol or Module for quantifying emissions from market leakage.
Total Market Leakage
Figure 1 provides an overview of the market leakage mechanisms included in this Module and their quantification approach.
Figure 1: Overview of market leakage mechanisms
Total market leakage is the sum of the market leakage from each market leakage mechanism.
(Equation 1)
Where:
- is the total emissions from market leakage in the Reporting Period, in tonnes of CO2e
- is the emissions from market leakage due to feedstock utilization, in tonnes of CO2e.
- is the emissions from market leakage due to energy utilization, in tonnes of CO2e.
- is the emissions from market leakage due to displacement of productivity, in tonnes of CO2e.
- is the emissions from market leakage due to reduction in productivity, in tonnes of CO2e.
has a minimum value of 0.
The Protocol defines the market leakage mechanisms that apply to a Project. Projects set terms that do not apply to them to 0.
Input Utilization
Where a Project consumes an input with an alternative market use, it adds to demand for the input. The market response depends on whether supply for the input is constrained. A supply-constrained input is one whose available quantity cannot easily or quickly be expanded by producers, even when consumer demand or prices increase.
- If supply is not constrained, producers supply more and existing consumers are unaffected, for example, where more corn stover can be collected. There is no market leakage. The input's production emissions are counted as Project Emissions under the GHG Accounting Module.
- If supply is constrained, existing consumers switch to a substitute. Market leakage is the amount by which the substitute's emissions exceed the input's Project Emissions. Only the additional emissions are counted since the production emissions of the input and the production emissions of the substitute product both correspond to the same tonne of input feedstock.
Section 3.1 covers feedstocks (biomass and mineral) and Section 3.2 covers energy from established sources.
Calculation of CO2eMarketLeakage,Feedstock,RP
Project Proponents must determine whether a feedstock is supply-constrained, and if so, identify its substitute product(s) for the alternative end-use(s). Suitable substitute products must be unconstrained marginal products. For each substitute product, Project Proponents must determine the ratio substitute product required on a like-for-function basis, and its emissions intensity. Where more than one substitute product could replace the consumed input in its alternative use, Project Proponents must use the one with the highest emissions per unit of function delivered.
Projects must quantify the emissions from market leakage due to utilization of supply-constrained feedstocks using Equation 2.
(Equation 2)
Where:
-
is the emissions from market leakage due to supply-constrained input utilization in the Reporting Period, in tonnes of CO2e.
-
is the number of batches consumed in the Reporting Period.
-
is the mass of batch supply-constrained feedstock consumed by the Project in tonnes as determined under the applicable Protocol.
-
is the quantity of substitute product needed to deliver the function of one unit of the supply-constrained input per tonne, on a like-for-function basis normalized to the property the alternative use depends on (mass or strength for aggregate, liming value for a soil amendment, delivered energy for a fuel).
-
is the production and transport emission factor of substitute product, in tonnes of CO2e per unit of substitute.
-
is the production and transport emissions per tonne of feedstock batch that are counted as Project Emissions under the GHG Accounting Module, in tonnes of CO₂e per tonne.
-
is emissions from activities caused by use of the substitute product that are not covered by such as additional transport, in tonnes of CO2e.
Below are a few representative examples of feedstocks, their alternative use and suitable substitute products:
-
Wood from bioenergy
- Feedstock: forest residues
- Alternative use: combustion for bioenergy
- Substitute Product: the remaining grid mix for electricity or the marginal fuel for heat
-
Manure from nutrient application
- Feedstock: manure
- Alternative use: soil-amendment
- Substitute Product: synthetic fertilizer
-
Mineral by-product from cement feed
- Feedstock: basalt fines
- Alternative use: cement
- Substitute Product: virgin raw material for cement input
Calculation of CO2eMarketLeakage,Energy,RP
Energy drawn directly from an established source that would otherwise have been dispatched to an electricity, heat or gas grid is also result in emissions caused from market leakage. An established energy source is defined as having entered service 36 months or more before Project initiation. Where an established energy source has been expanded, only the capacity that entered service 36 months or more before Project initiation is considered established.
Project Proponents must declare every established energy source from which energy is consumed from the grid to the Project. Projects must quantify the emissions from market leakage due to energy consumed from established energy sources using Equation 3, regardless of the type of on-site energy source.
(Equation 3)
Where:
- is the emissions from market leakage due to the Project's change in the dispatch of energy to the grid, in tonnes of CO2e.
- is the index of established energy sources.
- is the number of established energy sources.
- is the reduction in energy dispatched to the grid from source i caused by the Project in the Reporting Period, in MWh. is positive when dispatch falls.
- is the average grid emissions factor, in tonnes of CO2e/MWh. Requirements for acceptable emissions factors are in the Energy Use Accounting Module.
Increases in dispatch to the grid are set to 0 in Equation 3. Projects are not credited for exporting additional energy.
Displacement of Productivity
Displacement of productivity occurs when a Project takes land out of commodity production, or reduces the quantity of commodities that land produces. Some or all of the lost supply is replaced by production elsewhere, and converting land to supply that production causes market leakage through indirect land use change.
Displacement can happen once, when land is converted to a Project use (for example, reforestation or a purpose-grown feedstock on productive farmland). It can also accumulate over time when Project activities reduce yields on land that stays in production (for example, an intermediate crop or a change in soil management). For land conversion, which is a one-time event, market leakage is based on the initial quantity of displacement. Where the Project Site continues to produce the commodity, only additional displacement (above the highest level already counted) is included when quantifying market leakage emissions in subsequent Reporting Periods.
Calculation of CO2eMarketLeakage,Disp,RP
Projects must quantify emissions from market leakage due to displacement of productivity by multiplying the increase in displaced productivity of each commodity by that commodity's market leakage factor, then summing across all commodities:
(Equation 4)
(Equation 5)
Where:
- is the emissions from market leakage due to displacement of productivity in the Reporting Period, in tonnes of CO2e.
- is the displaced productivity of commodity c for the Reporting Period in tonnes per year. Where the Protocol assesses displacement once, is that value in the Reporting Period of assessment and in any later Reporting Period in which the Protocol revises it.
- is the highest quantity of displaced productivity of commodity c in any earlier Reporting Period of the Project, including earlier Crediting Periods; zero where there are none.
- is the increase in displaced productivity of commodity c above the highest level already included, in tonnes per year.
- is the market leakage factor for commodity c, in tCO2e per tonne per year of displaced productivity, applied once to each increase in displaced productivity. The method of determining depends on the displaced commodity:
- Where c is a CORSIA-modeled crop in Appendix A, or a substitute listed in Appendix B, Projects must determine using CORSIA-derived market leakage factors. See Section 4.1.1 for more details.
- Where c is any other crop or livestock, Projects must determine using IS and NL factors. See Section 4.1.2 for more details.
Displacement already accounted for in a Reporting Period is not counted again in subsequent Reporting Periods. Market leakage deductions are also permanent: if displacement later decreases, the Project cannot reclaim certificates previously deducted for market leakage. As a result, a given quantity of displaced productivity produces the same total market leakage whether the Protocol assesses it once or in every Reporting Period, and regardless of Crediting Period length.
Example (Equations 4 and 5): A biomass Project plants an intermediate crop in a corn rotation, which lowers corn yield by 1 tonne per acre relative to the baseline in Reporting Period 1. All of that is new displacement, so the full 1 tonne per acre is multiplied by the market leakage factor for corn. In Reporting Period 2:
- If the yield decline stays at 1 tonne per acre, the increase is 0 and no further market leakage is counted.
- If the yield decline rises to 1.2 tonnes per acre, only the 0.2 tonne per acre increase is counted.
- If the yield decline falls to 0.5 tonnes per acre, the increase is 0, and market leakage already counted is not reduced.
CORSIA-derived Market Leakage Factors
For globally traded commodity crops with a potential use in biofuel markets, CORSIA provides an established method for assessing ILUC emissions. This Section adopts the ILUC values published under CORSIA, adjusts them for use in this Module, and converts them into market leakage factors.
CORSIA Methodology
CORSIA developed default ILUC values for a defined set of feedstock-to-fuel pathways through a multi-year, internationally reviewed modeling exercise. Each value expresses the net global land-use change emissions induced by a marginal expansion of that feedstock for fuel, in grams of CO2e per megajoule of fuel, amortized over 25 years and net of co-product certificates.
The CORSIA values combine scenario results from two economic models:
- Global Trade Analysis Project, Biofuels variant (GTAP-BIO) Purdue University is a computable general equilibrium model. It represents the world economy and solves for a new market equilibrium after a biofuel-demand shock by letting relative prices adjust. Land competition is handled through a nested land-supply structure across agro-ecological zones. Its strength is capturing economy-wide feedbacks and cross-commodity substitution. GTAP-BIO is static and solves a single historical model period based on empirical data.
- Global Biosphere Management Model (GLOBIOM), IIASA is a partial equilibrium model of the land-use sectors and the interactions between agriculture, forestry and bioenergy. It is spatially explicit and bottom-up, resolving land and biophysical data (yields, carbon stocks, land availability) at fine resolution. It includes a biophysically grounded representation of where conversion occurs and what carbon that land holds. GLOBIOM is dynamic, solving over forward-looking model periods on a decadal basis.
The two models differ in scope, method, timeframe and data, so they yield different predictions on land-use responses. CORSIA ran each model for the same fuel pathways to produce two sets of results per pathway. CORSIA's default ILUC values are the mean of the two central estimates where GTAP-BIO and GLOBIOM results differ by 8.9 gCO2e/MJ or less, and the lower value plus 4.45 gCO2e/MJ where they differ by more.
This Module adopts the published values without re-running the models. Values are per unit of biofuel feedstock, taken from Table 129 of the CORSIA Supporting Document, CORSIA Eligible Fuels, Life Cycle Assessment Methodology, Version 8 (ICAO, November 2025)1.
Adjustments to CORSIA Values for Implementation
CORSIA values need two key adjustments before they can be used in this Module for market leakage estimation: a co-product gross-up, and a change of amortization period.
- Co-product gross-up. GTAP-BIO and GLOBIOM model a demand shock for fuel, such as corn grain for alcohol-to-jet or soybean oil for HEFA. These crops also produce animal-feed co-products, such as dried distillers grains with solubles (DDGS) and soybean meal. The co-products displace other feed, which lowers the modeled ILUC. Displacement under this Module removes the whole crop, so the comparable scenario is a crop shock, not a fuel shock. A co-product gross-up (Appendix A) corrects for the co-product effect, on an economic-allocation basis.
- Amortization period. CORSIA reports ILUC results amortized over 25 years. That period is a policy choice: a compromise between the 20 years typical in European policy and the 30 years used in US policy. Appendix A restates the values per tonne of whole crop on a 15-year basis. The choice of period does not change the total. This Module includes the full ILUC per tonne of displaced productivity once (Equation 4), so 15 years at the 15-year rate equals 25 years at CORSIA's rate.
Substitute Commodities to CORSIA-modeled crops
CORSIA-based ILUC emissions factors can also be applied for displaced commodities that are substitutes to crops directly modeled in GTAP-BIO and GLOBIOM (ICAO, November 2025)1. The list of substitute crops, their CORSIA analogs, and the matching basis is detailed in Appendix B. Each substitute shares supply characteristics as well as markets and end uses with its analog, so displacing it has a comparable market leakage effect.
Calculating the Market Leakage Factor
The market leakage factor for a CORSIA-modeled commodity, or a substitute, is:
(Equation 6)
Where:
- is the market leakage factor for commodity c, in tCO2e per tonne per year of displaced productivity, included once.
- is the whole-crop ILUC factor for commodity c from Appendix A on the 15-year basis, in tCO2e per tonne per year. For substitutes, the analog's value from Appendix B is used.
- = the amortization period, 15 years.
For oilseeds recorded as whole seed or fruit, in Equation 5 is converted to oil-equivalent tonnes first (Appendix A). Where a Project is in a region with a CORSIA-specific regional value, that regional value shall be used. Where a Project is located outside these regions, the value from the Global row must be used.
Example. A BiCRS Project using a purpose-grown feedstock displaces 100 t/yr of US corn grain at project establishment, and that is the only commodity displaced. = 0.373 × 15 = 5.60 tCO2e per t/yr, so is 560 tCO2e. The value 0.373 is CORSIA’s value restated as an annual rate over a 15-year basis. Multiplying by 15 gives the full leakage for each tonne per year displaced. The BiCRS Project takes this market leakage assessment once (100 × 5.60 = 560 tCO₂e), included in full in the first Reporting Period.
Increased Supply – New Land Market Leakage Factors (IS-NL)
For commodities not covered by Section 4.1.1, including livestock, the market leakage factor used in Equation 4 is calculated for each commodity from the land conversion that displacement induces:
(Equation 7)
Where:
- is the market leakage factor for commodity c, in tCO2e per tonne per year of displaced productivity, included once.
- is increased supply, the share of displaced productivity of commodity c replaced by increased supply elsewhere, as a fraction (Equation 8).
- is new land, the share of new agricultural land for the production type in the region that was natural land before conversion, as a fraction (Equation 9).
- is the carbon stock emission factor of the natural land before being converted, in tCO2e per hectare (Equation 10).
- is the yield on new land brought into production, in tonnes of commodity per hectare per year.
Increased Supply (IS)
Increased Supply (IS) is the share of displaced productivity that is replaced by increased supply elsewhere. Because supply and demand respond to price, displaced productivity is not replaced on a 1:1 basis. IS is therefore calculated from the price elasticities of supply and demand:
(Equation 8)
Where
- is the elasticity of supply for commodity c
- the elasticity of demand for commodity c
Default values for certain regions are in Appendix C. For other regions, values must be sourced from literature by the procedure in Appendix C.
New Land (NL)
New Land (NL) is the share of new agricultural land in a region, over a fixed reference period, that was natural land before conversion. It is defined separately for two production types:
- Cropland, for commodities produced on cropland, for example cocoa, coffee, grains, orchard crops, legumes and rice.
- Livestock, for commodities produced on pasture. Pasture is cultivated grassland.
NL is calculated from two characteristics of each parcel of land in the region:
- A parcel is new agricultural land for a production type if it is in that use at the end of the reference period, t1, and was not in that use at the start, .
- A parcel was natural land before conversion if its land cover at a baseline time, , before conversion was forest, grassland, shrubland or other natural vegetation.
Reference periods are
- Cropland: = 2003, = 2019, = the most recent imagery before the conversion of each parcel
- Livestock: = 2003-2005, = 2020-2022, = 2000. Where or spans three years, land use is the use observed in at least two of the three years.
(Equation 9)
Where:
- is the gross area of new agricultural land for the production type in the region over the reference period, including land converted from other agricultural uses, and
- is the part of that was forest, grassland, shrubland or other natural vegetation before conversion.
Projects must use the Appendix C value for their region.
Carbon Stock Emission Factor, EFCarbonStock
is the CO2 emitted per hectare of natural land before converted to agricultural use. Because NL covers all natural land, is the mean over the two types of natural land converted, forest and grassland, weighted by the share of converted area of each. For each land type, the emission is the carbon in living biomass, above and below ground. For conversion to cropland, the soil organic carbon lost is also included.
(Equation 10)
Where:
- , is the proportion of natural land converted to the production type in the region that were forest (tree cover of 3m or more) and grassland (all other natural vegetation) before conversion.
- is index of land types.
- is the mean pre-conversion above-ground biomass of land type k on land later converted, in tonnes of dry matter per hectare (ESA CCI Biomass v7.0).
- is the root-to-shoot ratio for land type k in the region sourced from IPCC 20062.
- is the carbon fraction of dry matter, 0.47 tonnes C per tonne of dry matter.
- is soil organic carbon lost on conversion to annual cropland, in tCO2e per hectare (AEZ-EF, Plevin et al. 2014)3; zero for conversion to pasture.
is calculated for each production type and region, includes the full pre-conversion stock (the carbon stock of the agricultural use that replaces it is not subtracted), and is a one-time emission that is not amortized. Projects use the Appendix C value for their production type and region.
Yield on New Land, YNL
is the average regional yield of commodity c over the most recent five years, from regional statistics (for example, USDA) or national statistics (for example, FAOSTAT) where regional data are unavailable, on the same basis as in Equation 5. For livestock it is the regional mean stocking rate.
Reduction in Productivity
A Project reduces productivity of land when it delays harvest (for example, deferred harvest of timber) or prevents it (for example, forest conservation). Projects must quantify emissions from market leakage due to reduced timber harvest with the Global Timber Model, which captures market and activity-shifting responses together (Section 5.1).
Calculation of CO2eMarketLeakage,GTM,RP
Reduced timber harvest is assessed with the Global Timber Model (GTM), which captures both direct landowner responses (activity-shifting) and market-mediated effects (market leakage) in one economic model. Isometric calculates leakage for each species group in each regional wood basket.
The GTM was conceptualized by Sohngen et al. (1999)[^2] and re-balances supply and demand in response to market shocks over decadal periods for forest type-regions. It was adapted for carbon projects in an update led by the University of Maine with The Nature Conservancy and the Global Forest Lab at Ohio State University (Daigneault et al. 2025), which estimates how forest carbon projects in aggregate change regional and global trade balances through leakage.
Isometric calculates the market leakage deduction for each Reporting Period from global runs of leakage rates for each forest type, annualized and weighted by the Project's basal area. Because the market response to a change in harvest lasts decades the schedule of annual leakage rates, , is set at Project initiation and updated by Isometric when new sites are added. Appendix D sets out the model parameters, data and forest type-region classifications.
The Project market leakage rate is calculated in three steps: the average market leakage rate for each forest type-region in each decade (Equation 11), the basal-area-weighted Project rate for each decade (Equation 12), and its annualization for the Reporting Period (Equation 13).
The average leakage rate for each forest type-region in each 10-year period is:
(Equation 11)
Where:
- = the average leakage rate in decade t for forest type f in region r, as a fraction. This includes market leakage and activity shifting leakage.
- = the carbon stock within the Project boundaries, in tonnes of C, in the Project and counterfactual scenarios.
- = the global forest carbon stock, in tonnes of C, in the Project and counterfactual scenarios.
- = the discount rate, 5%.
(Equation 12)
Where:
- = the Project leakage rate for decade t.
- = the basal area in each forest type-region in the Project area.
- = the total basal area in the Project area, equal to the sum of .
The GTM reports decadal values, so the rate is annualized by linear interpolation:
(Equation 13)
Where:
- = the Project leakage rate for the Reporting Period.
- , = the rates for the first and last year of the decadal time step.
- = the year into the decadal time step.
Where LProject,RP is below 10%, including where it is negative, Isometric applies a minimum annual leakage rate of 10%. Studies including Badgley et al. (2022) and Haya et al. (2023) found systematic over-crediting in forest carbon offset programs, largely because leakage was under-counted.
The final leakage deduction for each Reporting Period, can then be calculated as a percentage of the net sequestered carbon in a Reporting Period.
(Equation 14)
and are quantified in the respective Protocol.
Definitions and Acronyms
- BaselineA set of data describing pre-intervention or control conditions to be used as a reference scenario for comparison.
- By-productMaterials of value that are produced incidentally or as a residual of the production process.
- CORSIACarbon Offsetting and Reduction Scheme for International Aviation, administered by the International Civil Aviation Organization (ICAO).
- CertificateA publicly visible, uniquely identifiable, Verified instrument Issued on the Isometric Registry. Isometric Issues three Certificate Types: Carbon Dioxide Removal Certificates, Emission Reduction Certificates and Environmental Attribute Certificates.
- CommodityA product that has been cultivated, raised or harvested primarily for food, shelter, or natural fiber.
- Crediting PeriodThe period of time over which a Project Design Document is valid, and over which Removals, Reductions or Environmental Attributes may be Verified, resulting in Issued Certificates.
- Displacement of productivityA reduction in the output of a commodity from land used by a Project, where the Project does not consume that output.
- Emission FactorAn estimate of the emissions intensity per unit of an activity.
- Established energy sourceAn energy source, or part of a source’s capacity, that entered service 36 months or more before Project initiation.
- FeedstockRaw material which is used for CO₂ Removal or GHG Reduction.
- Increased Supply (IS)The share of displaced productivity that is replaced by increased supply elsewhere, calculated from the price elasticities of supply and demand.
- Indirect land-use change (ILUC)The market-mediated expansion of agricultural land that occurs from cropland being diverted to an alternate use.
- Input utilizationA Project’s consumption of an input that has an existing use, such as a biomass residue, a by-product or energy from an established source, where supply of the input cannot readily expand to meet the Project’s demand.
- Market leakageIncreased emissions outside of a Project’s system boundary that result from a Project’s effect on the market for a product or land: supply and demand re-equilibrate, and production or land use changes elsewhere. It arises through input utilization, displacement of productivity or reduction in productivity.
- Market leakage factor (LF)Market leakage per tonne per year of displaced productivity of a commodity, in tCO₂e per tonne per year.
- ModuleIndependent components of Isometric Certified Protocols which are transferable between and applicable to different Protocols.
- New Land (NL)The share of new agricultural land for a production type in a region, over a reference period, that was natural land before conversion.
- ProjectAn activity or process or group of activities or processes that alter the condition of a Baseline and leads to Removals or Reductions.
- Project ProponentThe organization that develops and/or has overall legal ownership or control of a Removal or Reduction Project.
- ProtocolA document that describes how to quantitatively assess the net amount of CO₂ removed by a process. To Isometric, a Protocol is specific to a Project Proponent's process and comprised of Modules representing the Carbon Fluxes involved in the CDR process. A Protocol measures the full carbon impact of a process against the Baseline of it not occurring.
- Reduction in productivityA Project’s deliberate reduction or deferral of timber harvest, for example by delaying harvest or setting timberland aside.
- ResidueA product that is not an economic driver of the process it is produced in.
- Substitute productThe product the market supplies to meet the use from which an input was diverted. It is the unconstrained marginal product for that use.
- System BoundaryGHG sources, sinks and reservoirs (SSRs) associated with the project boundary and included in the GHG Statement.
Appendix A: CORSIA ILUC Values in Feedstock-tonnage Terms, 15-year Amortization Basis
Table A1. CORSIA ILUC values and market leakage factors.
Values in the ILUC column are on CORSIA's 25-year basis, from Table 129 of the CORSIA LCA Methodology, Version 8. The fuel-attributed value is shown for transparency. Oilseed rows are per tonne of oil.
Commodity | Region | CORSIA pathway | ILUC, CORSIA 25-yr (kgCO2e/t) | Fuel-attributed, 15-yr (tCO2e/t per yr) | EFILUC,c whole-crop, 15-yr (tCO2e/t per yr) | MLFc (tCO2e per t/yr) |
|---|---|---|---|---|---|---|
Corn grain | USA | ATJ | 163.4 | 0.27 | 0.37 | 5.60 |
Corn grain | Global | ATJ | 227.2 | 0.38 | 0.52 | 7.78 |
Sugarcane | Brazil | ATJ | 14.9 | 0.02 | 0.03 | 0.40 |
Sugarcane | Global | ATJ | 14.5 | 0.02 | 0.03 | 0.39 |
Sugar beet | EU | SIP | 46.8 | 0.08 | 0.09 | 1.40 |
Sugar beet | Global | SIP | 26.1 | 0.04 | 0.05 | 0.78 |
Soybean oil | USA | HEFA | 925.6 | 1.54 | 4.60 | 68.96 |
Soybean oil | Brazil | HEFA | 1,020.0 | 1.70 | 5.07 | 75.99 |
Soybean oil | Global | HEFA | 974.7 | 1.62 | 4.84 | 72.62 |
Rapeseed / canola oil | EU | HEFA | 917.9 | 1.53 | 2.10 | 31.44 |
Rapeseed / canola oil | Global | HEFA | 990.3 | 1.65 | 2.26 | 33.92 |
Palm oil (CPO) | Malaysia/Indonesia | HEFA | 1,477.1 | 2.46 | 2.76 | 41.36 |
For soybean oil, rapeseed/canola oil and palm oil, EFILUC,c is expressed per tonne of vegetable oil. Where the displaced commodity is recorded as the whole oilseed or fruit, must be converted to oil-equivalent (OE) tonnes by multiplying by OEc (tonnes of oil per tonne of commodity, on the same moisture basis), taken from Agri-footprint v7 or a justified published extraction rate. Where the commodity is recorded as oil, OEc = 1.
Rescaling to a 15-year Basis
CORSIA values on the 25-year basis are converted to tCO2e per tonne per year on the 15-year basis:
(Equation A.1)
Where:
- = the CORSIA value for commodity c on the 25-year basis, in kgCO2e per tonne of feedstock (Table A1).
- = the fuel-attributed value for commodity c on the 15-year basis, in tCO2e per tonne per year.
Co-product Gross-up
The fuel-attributed value is converted to a whole-crop value by dividing by the fuel product's economic value share, expressed as a gross-up factor:
(Equation A.2)
Where:
- = the whole-crop ILUC factor for commodity c on the 15-year basis, in tCO2e per tonne per year (Table A1).
- = the fuel-attributed value for commodity c, from Equation A.1.
- = the co-product gross-up factor for commodity c (Table A2).
Table A2. Co-product Gross-up Factors
Commodity | GUc | Source |
|---|---|---|
Corn grain | 1.37 | Iowa State University CARD |
Sugarcane | 1.08 | Macedo, Seabra and Silva (2008) |
Sugar beet | 1.20 | Klenk et al. (2012) |
Soybean oil | 2.98 | Agri-footprint v7, non-EU values |
Rapeseed / canola oil | 1.37 | Agri-footprint v7, non-EU values |
Palm oil (CPO) | 1.12 | Agri-footprint v7, non-EU values |
Appendix B: CORSIA-modeled Crop Substitutes
Table B1. Substitute crops and CORSIA analogs
Displaced commodity | CORSIA analog | Basis for the match | Matching basis |
|---|---|---|---|
Wheat | Corn grain | Temperate cereal; shares the feed, food and starch-ethanol markets | Bone-dry tonne, 1:1 |
Barley | Corn grain | Temperate feed grain | Bone-dry tonne, 1:1 |
Grain sorghum | Corn grain | Feed and ethanol grain; near-direct substitute for corn | Bone-dry tonne, 1:1 |
Oats, rye, triticale | Corn grain | Minor temperate feed grains | Bone-dry tonne, 1:1 |
Sweet sorghum | Sugarcane | Sugar and ethanol feedstock | Bone-dry tonne, 1:1 |
Sunflower seed | Rapeseed / canola oil | Temperate oilseed; oil-plus-meal co-product structure | Oil-equivalent (Appendix A) |
Safflower, camelina | Rapeseed / canola oil | Temperate oilseeds | Oil-equivalent (Appendix A) |
Cottonseed | Soybean oil | Oilseed with a meal-dominant value split | Oil-equivalent (Appendix A) |
Groundnut (peanut) | Rapeseed / canola oil | Oilseed with high oil content and an oil-dominant value split | Oil-equivalent (Appendix A) |
Coconut, declared as copra | Palm oil (CPO) | Tropical perennial oil crop; tropical-oil market | Oil-equivalent (Appendix A), OE = 0.63 |
Coconut, declared as coconut oil | Palm oil (CPO) | Tropical perennial oil crop; tropical-oil market | Oil-equivalent (Appendix A), OE = 1 |
Other tropical vegetable oils, declared as oil (e.g., palm kernel oil, babassu) | Palm oil (CPO) | Tropical vegetable-oil market; near-fungible at the refined level, with palm the marginal supplier | Oil-equivalent (Appendix A), OE = 1 |
Appendix C: Default Values for IS, NL and EFCarbonStock
Increased Supply (IS)
IS represents the share of production that is supplied from other locations.
Isometric has carried out a literature review of εs and εd values to inform IS for certain regions. Where the Project falls in these regions, the defaults must be used unless alternative values are approved by Isometric. The default values also serve as examples of appropriate values. The regions considered in the IS literature review were Brazil, Panama, Mexico and the United States, selected after a review of expected Project demand. Isometric will add regions based on demand; values for other regions are reviewed case by case.
Where there is not an existing default value, εs and εd values must be sourced as follows:
- Define a crop-region pair broad enough that cross-effects with all other crops and regions are negligible. For livestock, "beef in Mato Grosso" is too specific and "all meat globally" is too broad; "beef in South America" may strike the balance.
- Search the academic literature for papers estimating supply and demand elasticities for the crop-region pair or a similar pair.
- Confirm the paper meets these criteria: it uses a dynamic panel or instrumental variables technique; it is based on time-series rather than cross-sectional variation in prices; it was published in the last 15 years in a reputable economics or land-use journal, or in a report for a reputable organization such as the EU or CARB; it states whether the estimate is short-run or long-run; and it uses planting-season prices.
- Calculate IS from the supply and demand elasticities with Equation 8.
Where no literature exists for the relevant context, the most similar available default can be used. For example, coffee can be a suitable default for cocoa. Where possible, supply and demand elasticities should be estimated in the same paper, and the paper should be cited by a reputable organization compiling a meta-analysis or parameterizing a partial-equilibrium model for policy analysis, such as CARB, the EU or FAO.
Table C1. IS default values
Geography | Crop | εd,c | εs,c | IS | Key citation |
|---|---|---|---|---|---|
Global | Calories (rice, wheat, corn, soy) | −0.05 | 0.12 | 0.70 | Roberts and Schlenker (2013) |
Global | Coffee | −0.305 | 0.285 | 0.48 | Akiyama and Varangis (1990) |
Global | Cocoa | −0.075 | 0.075 | 0.50 | Askari and Cummings (1977); Behrman (1965) |
South America | Livestock | −0.40 | 0.40 | 0.50 | Fragoso et al. (2011) |
North America | Livestock | −0.40 | 1.60 | 0.80 | Mintert et al. (2009); Jeong (2019) |
Carbon Stock Emissions Factor (EFCarbonStock)
is estimated from the same sample of one-degree cells as livestock NL. For livestock, land-type shares come from the same observations as NL. Above-ground biomass is read for 2005, the earliest year available, at up to 50 pixels of new pasture in each sampled cell and up to 30 pixels of new cropland in each of a random 75 sampled cells per region. Forest already cleared by 2005 (above-ground biomass below 10 tonnes of dry matter per hectare in both 2005 and 2020) has no observable pre-conversion biomass and is excluded.
Table C4. Data sources for EFCarbonStock
Parameter | Description | Source |
|---|---|---|
, , cropland | Land cover before conversion of new cropland | GLAD Global Land Cover and Land Use Change, version 2, 30 m (Potapov et al. 2022b)6 |
, , livestock | Land cover in 2000 of new pasture | Global Pasture Watch, version 2 (Parente et al. 2024)5; GLAD Global Land Cover and Land Use Change, version 2 (Potapov et al. 2022b)6 |
Above-ground biomass before conversion on converted natural land, 100 m | ESA Climate Change Initiative Biomass, version 7.0 (Santoro and Cartus)7 | |
Root-to-shoot ratio by land type and region: the area-weighted average of IPCC vegetation-class values, weighted by the share of regional land in each climate zone | IPCC (2006), Volume 42 | |
Carbon fraction of dry matter, 0.47 | IPCC (2006), Volume 42 | |
Soil organic carbon lost on conversion to annual cropland, by agro-ecological zone | AEZ-EF model (Plevin et al. 2014)3 |
Table C5. EFCarbonStock default values (tCO2e per hectare)
Region | Cropland | Livestock |
|---|---|---|
Africa | 140 | 65 |
East & Southeast Asia | 137 | 163 |
North & Central America | 166 | 90 |
South America | 177 | 99 |
Defaults for South & West Asia, Australia & New Zealand, and Europe & North Asia are in development. Until they are published, values for these regions are calculated with Equations 10a and 10b from the sources in Table C4 and approved by Isometric.
Appendix D: Implementation of the Global Timber Model
Isometric implements the 2025 version of the Global Timber Model (GTM) . Key parameters used are summarized in Table D1. The GTM uses a global implementation rate representing the share of all forest land globally unavailable for harvest due to being enrolled in forest carbon projects.
Isometric determines harvest eligibility by accessibility, so all accessible forests are eligible. Forest area reported in the FAO Forest Resources Assessment as "protected" is excluded. Based on an analysis of all forest-based carbon projects conducted in June 2024 by Renoster, the total global area enrolled in forest carbon projects was 77.599 Mha, representing approximately 8% of the total available forest area. Research by Haya et al. (2023)[^4,20], Stapp et al. (2023)[^21] and others suggests that most forest carbon projects greatly overestimate emission reductions and that enrollment has historically been unlikely to reduce near-term harvesting or deforestation. Isometric therefore assumes that the area of carbon project land on which all harvest is prevented is 50% of the calculated 8%, and applies a global carbon project implementation rate of 4%.
Table D1. Key variables in the GTM for leakage assessment
Variables | Value | Same as used in Daigneault et al. 2025 | Explanation |
|---|---|---|---|
Annual discount rate | 5.00% | Yes | Commonly assumed to represent the average expected rate of return in the global forest sector |
Global carbon project implementation rate | 4.00% | No | A conservative accounting of forest area unavailable for commercial harvest due to carbon projects |
Elasticity of management intensity to timber price | Variable | Yes | Set for each region |
Elasticity of timber demand to timber price | -1.0 | Yes | Substitutions occur over decade-long timesteps in GTM, and in aggregate are more likely than single substitutions in single years. See Sohngen 2024 for additional explanation. |
Elasticity of land area in forest to timber price | 0.3 | Yes | Based on Lubowski et al. 2006, Sohngen et al. 2019 |
Forest Type-region Classifications
Isometric matches the species present in the Project area to a GTM forest type and region (Tables D2 and D3). The forest types are based on the 2010 UN FAO Global Ecological Zones, with finer resolution for United States forest types based on USFS FIA regional groupings. Where species or genera are not listed in the GTM forest types, authoritative sources, including local foresters and the Wood Database, are consulted to find the type with similar commercial use and ecological characteristics.
Table D2. Forest type and region classification for the United States
Forest Type | Region | Forest Type Description | Region Description |
|---|---|---|---|
Pine | Southeast | Pine species grown naturally or commercially, including loblolly pine (Pinus taeda), slash pine (P. elliottii), longleaf pine (P. palustris), and shortleaf pine (P. echinata) | Virginia, North Carolina, South Carolina, Georgia, Florida, Alabama, Mississippi, Louisiana |
EHW | Eastern non-oak hardwood species grown naturally or commercially, including sweetgum (Liquidambar styraciflua), yellow-poplar (Liriodendron tulipifera), and red maple (Acer rubrum) | ||
Oak | Oak species (Quercus spp.) including white oak (Q. alba), northern red oak (Q. rubra), southern red oak (Q. falcata), and post oak (Q. stellata) | ||
Pine | South-Central | Pine species including shortleaf pine (Pinus echinata), loblolly pine (P. taeda), and pitch pine (P. rigida) | Kentucky, Tennessee, Arkansas, Oklahoma |
EHW | Eastern non-oak hardwood species including tulip tree (Liriodendron tulipifera), sweetgum (Liquidambar styraciflua), and black walnut (Juglans nigra) | ||
Oak | Oak species including white oak (Quercus alba), black oak (Q. velutina), and chestnut oak (Q. prinus) | ||
SF | Northeast | Spruce-fir forest types including red spruce (Picea rubens), balsam fir (Abies balsamea), and eastern hemlock (Tsuga canadensis) | Maine, New Hampshire, Vermont, Massachusetts, Rhode Island, Connecticut, New York, Pennsylvania |
Pine | Northern pine species including eastern white pine (Pinus strobus), red pine (P. resinosa), and jack pine (P. banksiana) | ||
EHW | Eastern hardwood species including sugar maple (Acer saccharum), American beech (Fagus grandifolia), and yellow birch (Betula alleghaniensis) | ||
Oak | Oak species including northern red oak (Quercus rubra), white oak (Q. alba), and chestnut oak (Q. prinus) | ||
SF | North-Central | Spruce-fir complexes including white spruce (Picea glauca), balsam fir (Abies balsamea), and northern white-cedar (Thuja occidentalis) | Minnesota, Wisconsin, Michigan, Iowa, Missouri, Illinois, Indiana, Ohio |
Pine | Northern pine species including red pine (Pinus resinosa), jack pine (P. banksiana), and eastern white pine (P. strobus) | ||
EHW | Hardwood species including sugar maple (Acer saccharum), American basswood (Tilia americana), and northern red oak (Quercus rubra) | ||
Oak | Oak species including bur oak (Quercus macrocarpa), white oak (Q. alba), and northern red oak (Q. rubra) | ||
DF | West | Douglas-fir (Pseudotsuga menziesii) and associated coniferous species including western hemlock (Tsuga heterophylla) and grand fir (Abies grandis) | California, Oregon, Washington |
Pine | Western pine species including ponderosa pine (Pinus ponderosa), sugar pine (P. lambertiana), and lodgepole pine (P. contorta) | ||
HW | Western hardwood species including red alder (Alnus rubra), bigleaf maple (Acer macrophyllum), and Oregon white oak (Quercus garryana) | ||
SW | Softwood species other than Douglas-fir and pine, including western redcedar (Thuja plicata), western hemlock (Tsuga heterophylla), and true fir species (Abies spp.) | ||
HW | Southwest | Southwestern hardwood species including Fremont cottonwood (Populus fremontii), Arizona sycamore (Platanus wrightii), and Gambel oak (Quercus gambelii) | Texas, New Mexico, Arizona |
DF | Douglas-fir (Pseudotsuga menziesii) adapted to southwestern growing conditions | ||
Pine | Mountain | Mountain pine species including ponderosa pine (Pinus ponderosa), lodgepole pine (P. contorta), and limber pine (P. flexilis) | Montana, Wyoming, Colorado, Idaho, Nevada, Utah |
HW | Mountain hardwood species including quaking aspen (Populus tremuloides), Rocky Mountain maple (Acer glabrum), and paper birch (Betula papyrifera) |
Table D3. Forest type and region classification for countries and regions other than the United States
Forest Type | Region | Forest Type Description | Region Description |
|---|---|---|---|
Plantation | China | Fast-growing plantation species including eucalyptus (Eucalyptus spp.), poplar (Populus spp.), and Chinese fir (Cunninghamia lanceolata) under intensive management | All administrative regions with forest plantation development |
Natural | Natural forest ecosystems including mixed temperate forests, boreal forests, and subtropical forests with native species composition | ||
S. Plt. | Brazil | Short-rotation plantation forestry focused on eucalyptus (Eucalyptus spp.) and pine (Pinus spp.) for industrial wood production | All states with plantation forestry operations |
Trop. Evergreen | Tropical evergreen rainforest including Amazon rainforest with diverse hardwood species | Primarily Amazon Basin states | |
Trop. Mixed | Tropical mixed forests including Atlantic Forest remnants and Cerrado formations | Atlantic coast regions and central Cerrado | |
Atlantic/MW HW | Canada | Atlantic and Maritime hardwood forests including sugar maple (Acer saccharum), yellow birch (Betula alleghaniensis), and American beech (Fagus grandifolia) | Atlantic Maritime provinces |
Atlantic/MW SW | Atlantic and Maritime softwood forests dominated by red spruce (Picea rubens), balsam fir (Abies balsamea), and eastern hemlock (Tsuga canadensis) | ||
Atlantic/MW Mx | Atlantic and Maritime mixed forests combining hardwood and softwood species | ||
Boreal/Hudson HW | Boreal hardwood forests including paper birch (Betula papyrifera), trembling aspen (Populus tremuloides), and balsam poplar (P. balsamifera) | Hudson Bay lowlands region | |
Boreal/Hudson SW | Boreal softwood forests including black spruce (Picea mariana), white spruce (P. glauca), and jack pine (Pinus banksiana) | ||
Boreal/Hudson MX | Boreal mixed forests combining deciduous and coniferous species in the Hudson Bay region | ||
Taiga HW | Northern taiga hardwood species including paper birch (Betula papyrifera) and trembling aspen (Populus tremuloides) | Northern territories and provinces | |
Taiga SW | Taiga softwood forests dominated by black spruce (Picea mariana) and tamarack (Larix laricina) | ||
Taiga Mx | Taiga mixed forests combining hardwood and softwood species in extreme northern climates | ||
Boreal West HW | Western boreal hardwood forests including trembling aspen (Populus tremuloides), balsam poplar (P. balsamifera), and paper birch (Betula papyrifera) | Western boreal regions | |
Boreal West SW | Western boreal softwood forests including white spruce (Picea glauca), black spruce (P. mariana), and lodgepole pine (Pinus contorta) | ||
Boreal West MX | Western boreal mixed forests representing transitions between hardwood and softwood stands | ||
Boreal Montane HW | Montane boreal hardwood forests including trembling aspen (Populus tremuloides) and paper birch (Betula papyrifera) | Rocky Mountain and cordilleran regions | |
Boreal Montane SW | Montane boreal softwood forests including subalpine fir (Abies lasiocarpa), Engelmann spruce (Picea engelmannii), and lodgepole pine (Pinus contorta) | ||
Boreal Montane Mx | Mixed montane boreal forests combining elevation-adapted hardwood and softwood species | ||
Pacific HW | Pacific coast hardwood forests including red alder (Alnus rubra) and bigleaf maple (Acer macrophyllum) | British Columbia coastal regions | |
Pacific SW | Pacific coast softwood forests dominated by western hemlock (Tsuga heterophylla), western redcedar (Thuja plicata), and Douglas-fir (Pseudotsuga menziesii) | ||
Pacific Mx | Pacific coast mixed forests combining coastal hardwood and softwood species | ||
Conifer | Russia | Russian coniferous forests including Siberian pine (Pinus sibirica), Siberian spruce (Picea obovata), and Siberian fir (Abies sibirica) | Siberian and Far East regions |
Temp HW | Temperate hardwood forests including birch (Betula spp.), aspen (Populus spp.), and oak species (Quercus spp.) | European Russia and southern regions | |
Bor HW | Boreal hardwood forests dominated by birch (Betula spp.) and aspen (Populus spp.) | Northern boreal zone | |
HW | General hardwood forest classification for mixed deciduous species | Various regions with hardwood forest presence | |
Nord. Plt. | European Union | Nordic plantation forestry including Norway spruce (Picea abies), Scots pine (Pinus sylvestris), and managed species | Scandinavia and northern European countries |
Ce.S. Plt. | Central European softwood plantations including Norway spruce (Picea abies) and silver fir (Abies alba) | Germany, Austria, Czech Republic, and surrounding regions | |
Ce.H.Plt. | Central European hardwood plantations including European beech (Fagus sylvatica) and oak species (Quercus spp.) | ||
So.S.Plt. | Southern European softwood plantations including maritime pine (Pinus pinaster) and stone pine (P. pinea) | Mediterranean countries | |
So.H.Plt. | Southern European hardwood plantations including cork oak (Quercus suber), holm oak (Q. ilex), and eucalyptus (Eucalyptus spp.) | ||
E. SW | Eastern European softwood forests including Norway spruce (Picea abies) and Scots pine (Pinus sylvestris) | Eastern European member states | |
E. HW | Eastern European hardwood forests including European beech (Fagus sylvatica), oak species (Quercus spp.), and hornbeam (Carpinus betulus) | ||
Temp HW | Europe (Non-EU) | Temperate hardwood forests in non-EU European countries including beech (Fagus spp.) and oak (Quercus spp.) | Non-EU European countries including Switzerland, Norway, and Balkans |
Temp SW | Temperate softwood forests including Norway spruce (Picea abies) and Scots pine (Pinus sylvestris) | ||
Temperate Mixed | Mixed temperate forests combining hardwood and softwood species | ||
LR PLT | South Asia | Large-rotation plantation forestry including teak (Tectona grandis) and sal (Shorea robusta) | India, Pakistan, Bangladesh, and surrounding countries |
Tropical | Tropical forests including monsoon forests, dry deciduous forests, and wet evergreen forests | ||
S PLT | Central America | Small-scale plantation forestry including coffee shade trees and mahogany (Swietenia spp.) | Mexico, Guatemala, Belize, Honduras, El Salvador, Nicaragua, Costa Rica, Panama |
TMP EVER | Temperate evergreen forests including cloud forests and pine-oak forests | ||
TMP MX | Temperate mixed forests combining coniferous and deciduous species | ||
TMP DC | Temperate deciduous forests including oak forests and mixed deciduous formations | ||
S PLT | Rest of South America | Short-rotation plantation forestry including eucalyptus (Eucalyptus spp.) and pine (Pinus spp.) | Countries other than Brazil |
TR EVER | Tropical evergreen rainforests including Amazon basin forests | ||
TR MIX | Tropical mixed forests including seasonal dry forests and forest-savanna mosaics | ||
TEMP MX | Temperate mixed forests including Valdivian rainforest and Andean mixed forests | ||
S PLT | Sub-Saharan Africa | Short-rotation plantation forestry including eucalyptus (Eucalyptus spp.) and wattle (Acacia spp.) | African countries south of the Sahara Desert |
TR EV | Tropical evergreen forests including Congo Basin rainforests and East African montane forests | ||
TR MIX | Tropical mixed forests including miombo woodlands and moist forests | ||
Dipt | Southeast Asia | Dipterocarp forests dominated by Dipterocarpaceae family species characteristic of Southeast Asian rainforests | Indonesia, Malaysia, Thailand, Philippines, Vietnam, and surrounding countries |
Trop. Dry | Tropical dry forests including monsoon forests and deciduous forests | ||
Trop. Moist | Tropical moist forests including lowland rainforests and wet evergreen formations | ||
S. Plt. | Short-rotation plantation forestry including oil palm (Elaeis guineensis), rubber (Hevea brasiliensis), and timber species | ||
Temp | Oceania | Temperate forests including sclerophyll forests and wet temperate rainforests | Australia, New Zealand, and Pacific Islands |
Trop. Dry | Tropical dry forests and woodlands adapted to seasonal rainfall | ||
Trop. Moist | Tropical moist forests including wet tropical rainforests | ||
S. Plt. | Short-rotation plantation forestry including eucalyptus (Eucalyptus spp.) and pine (Pinus spp.) | ||
Temperate | Japan | Temperate forests including deciduous broad-leaved forests and mixed forests | All prefectures |
S PLT | Short-rotation plantation forestry including Japanese cedar (Cryptomeria japonica) and other managed species | ||
TR EVER | Africa and Middle East | Tropical evergreen forests in limited areas with suitable tropical climate | Limited tropical forest areas |
TR MIX | Tropical mixed forests and woodlands including dry forests and savanna-forest transitions | Various countries in Africa and Middle East |
Acknowledgements
Isometric would like to thank the following contributors to this Module:
Matthew Gammans, Ph.D. (North Dakota State University)
References
[^2] Sohngen, B., Mendelsohn, R., & Sedjo, R. (1999). Forest management, conservation, and global timber markets. American Journal of Agricultural Economics, 81(1), 1-13. https://doi.org/10.2307/1244446
[^3] Badgley, G., Freeman, J., Hamman, J. J., Haya, B., Trugman, A. T., Anderegg, W. R., & Cullenward, D. (2022). Systematic over‐crediting in California's forest carbon offsets program. Global Change Biology, 28(4), 1433-1445. https://doi.org/10.1111/gcb.15943
[^4] Haya, B. K., Evans, S., Brown, L., Bukoski, J., Butsic, V., Cabiyo, B., ... & Sanchez, D. L. (2023). Comprehensive review of carbon quantification by improved forest management offset protocols. Frontiers in Forests and Global Change, 6, 958879. https://doi.org/10.3389/ffgc.2023.958879
[^20] Haya, B. K., Alford-Jones, K., Anderegg, W. R., Beymer-Farris, B., Blanchard, L., & Bomfim, B. (2023). Quality assessment of REDD+ carbon credit projects. https://gspp.berkeley.edu/assets/uploads/page/Quality-Assessment-of-REDD+-Carbon-Crediting.pdf
[^21} Stapp, J., Nolte, C., Potts, M., Baumann, M., Haya, B. K., & Butsic, V. (2023). Little evidence of management change in California’s forest offset program. Communications Earth & Environment, 4(1), 331. https://doi.org/10.1038/s43247-023-00984-2
Footnotes
-
ICAO. (2025). CORSIA Supporting Document: CORSIA Eligible Fuels, Life Cycle Assessment Methodology, Version 8. International Civil Aviation Organization. https://www.icao.int/sites/default/files/environmental-protection/CORSIA/Documents/CORSIA%20Eligible%20Fuels/CORSIA_Supporting_Document_CORSIA-Eligible-Fuels_LCA_Methodology_V8.pdf ↩ ↩2
-
IPCC. (2006). 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 4: Agriculture, Forestry and Other Land Use. Hayama, Japan: Institute for Global Environmental Strategies. ↩ ↩2 ↩3
-
Plevin, R. J., Gibbs, H. K., Duffy, J., Yui, S., & Yeh, S. (2014). Agro-ecological Zone Emission Factor (AEZ-EF) Model (v47). GTAP Technical Paper No. 34. West Lafayette, IN: Purdue University. ↩ ↩2
-
Potapov, P., Turubanova, S., Hansen, M. C., Tyukavina, A., Zalles, V., Khan, A., Song, X.-P., Pickens, A., Shen, Q., & Cortez, J. (2022). Global maps of cropland extent and change show accelerated cropland expansion in the twenty-first century. Nature Food, 3(1), 19-28. https://doi.org/10.1038/s43016-021-00429-z ↩
-
Parente, L., Sloat, L., Mesquita, V., Consoli, D., Stanimirova, R., Hengl, T., ... & Ferreira, L. (2024). Annual 30-m maps of global grassland class and extent (2000-2022) based on spatiotemporal machine learning. Scientific Data, 11, 1303. https://doi.org/10.1038/s41597-024-04139-6 ↩ ↩2
-
Potapov, P., Hansen, M. C., Pickens, A., Hernandez-Serna, A., Tyukavina, A., Turubanova, S., ... & Kommareddy, A. (2022). The global 2000-2020 land cover and land use change dataset derived from the Landsat archive: first results. Frontiers in Remote Sensing, 3, 856903. https://doi.org/10.3389/frsen.2022.856903 ↩ ↩2 ↩3
-
Santoro, M., & Cartus, O. (n.d.). ESA Biomass Climate Change Initiative (Biomass_cci): Global datasets of forest above-ground biomass, version 7.0. NERC EDS Centre for Environmental Data Analysis. ↩
Contributors




